To connect an M.2 NVMe or M.2 SATA Drive: Slide all Locking Pins away from the M.2 Sockets. Align the M.2 SSD to the Socket with the M-key notch positioned to...

Users upgrading their computer hardware often need to make a duplicate of their SATA HDD or SSD on a high-performance M.2 NVMe or M.2 SATA drive. The KanguruClo...

Question Answer Is the duplicator able to copy SATA M.2? Yes, the KanguruClone M.2 NVMe Duplicator supports both PCIe M.2 and SATA M.2 natively....

All operation of the KanguruClone 11 NVMe is done using the touch-screen display. Once the duplicator boots up, you see the Main Menu screen. All the main func...

To Erase drives connected to the duplicator: Connect the drives to be erased to the duplicator. Note: By default, the Erase operation is not performed on the...

Sanitize Erase is a set of firmware commands available on many ATA drives. These commands are used as a secure method of data sanitization by completely overwri...

Secure Erase is a set of firmware commands available on many ATA drives. These commands are used as a secure method of data sanitization by completely overwriti...

The KanguruClone can copy data from a Source drive to Target drives in one of five modes: Full FULL mode copies/compares drives sector by sector from the...

Load function allows you to store disk image files to a Storage Center drive. A Storage Center drive is an NVMe drive that has been formatted to store image fil...

The Ratio mode allows you to copy or compare a defined percentage of the Source drive. The Source drive is divided in 1000 units. You must define the beginning...

Verify will check all connected drives and determine if they are readable. The verification operation will check any drive connected to a Target port and verifi...

Hardware Setup Place the KanguruClone where there is proper ventilation. Avoid using the KanguruClone in environments with high temperatures. Make sure that su...

KanguruClone M.2 NVMe Duplicators support PCIe M.2 SSDs, commonly known as NVMe SSDs as well as SATA M.2 SSDs. Both SATA M.2 and PCIe M.2 SSDs use a similar p...

Front View Side View Rear View

The settings can be accessed by tapping on the Settings icon located at the bottom right of the Main menu. Copy Copy provides the ability to set options t...

The Copy options provides the ability to set options to perform before the copy process starts as well after the copy process completes. Additionally, you are...

Erase Settings allows you the ability to set customer erase settings as well as number of cycles performed during the wipe process. Write 0 Overwrite all...

Format allows you to choose what file system the format feature uses as well as allows you to format for the connected drives. You can select the file system th...

Misc Settings allow you to alter system-based settings. These settings do not alter operations with the drives but rather base settings. Machine Name Giv...

Options Settings allow you to alter operation-based settings. These settings alter its operations with drives not the system-based settings. Capacity Check...

In order to perform a Ratio Copy, you must set the beginning and ending percentages. Ratio Head Define the ratio head start and end boundaries. The defaul...

Model KCLONE-11NVME Interface M.2 M-keyed M.2 B+M-keyed Drive Support PCIe based NVMe SSD SATA based M.2 SSD Display Full-color...

The duplicator will not boot or freezes curing boot. The device has media (drives) connected to it while powering on. Power the device off and disconnec...

One of the main features of the KanguruClone 4 M.2 NVMe Duplicator is the touchscreen user interface. If you are having issues with the accuracy of the touchscr...

The KanguruClone 4 NVMe supports NVMe SSDs that have an M.2 M-keyed connector as well as SATA M.2 B+M-keyed connectors. To connect an M.2 solid state drive to t...

Question Answer Do all Target drives have to be the same capacity? If you select Full copy or Brief copy, the Target drives must have at least the s...

All operation of the KanguruClone 4 NVMe is done using the touch-screen display. Once the duplicator boots up, you see the Main Menu screen. All the main funct...

To Erase drives connected to the duplicator: Connect the drives to be erased to the duplicator. Note: By default, the Erase operation is not performed on the d...

The KanguruClone can copy data from a Source drive to Target drives in one of five modes: Full FULL mode copies/compares drives sector by sector from the...

Load allows you to access image files saved on a Storage Center drive. A Storage Center drive is an NVMe drive that has been formatted to store image files of...

The Ratio mode allows you to copy or compare a defined percentage of the Source drive. The Source drive is divided in 1000 units. You must define the beginnin...

Verify will check all connected drives and determine if they are readable. The verification operation will check any drive connected to a Target port and verifi...

Hardware Setup Place the KanguruClone where there is proper ventilation. Avoid using the KanguruClone in environments with high temperatures. Make sure that su...

KanguruClone M.2 NVMe Duplicators support PCIe M.2 SSDs, commonly known as NVMe SSDs as well as SATA M.2 SSDs. Both SATA M.2 and PCIe M.2 SSDs use a similar p...

The Maxi Management software allows you to connect and manage a duplicator with a PC. Maxi Management software (henceforth referred to as Maxi) is only compatib...

If you are using the storage center, Brief Load is used to build a data image of a Source drive connected to the duplicator’s Source port, and save it loc...

If you are using the storage center, Full Load is used to build a full disk image of a Source drive connected to the duplicator’s Source port, and save it...

If you are using the storage center, Restore or load an image file saved on the host PC to a Source drive connected to the KanguruClone’ s Source port. O...

Front View Side View Rear View

Advanced Settings allow you to alter system-based settings. These settings do not alter operations with the drives but rather base settings. System Time...

The Copy options provides the ability to set options to perform before the copy process starts as well after the copy process completes. Additionally, you are...

Erase Settings allows you the ability to set customer erase settings as well as number of cycles performed during the wipe process. Methods Configure a CU...

Network settings must be configured if you are using the Maxi PC software to access the Duplicator over a LAN. The address information is only able to be viewed...

Options Settings allow you to alter operation-based settings. These settings alter its operations with drives not the system-based settings. Capacity Check...

In order to perform a Ratio Copy, you must set the beginning and ending percentages. Ratio Head Define the ratio head start and end boundaries. The defaul...

The settings can be accessed by tapping on the Settings icon located at the bottom right of the Main menu. Copy Copy provides the ability to set options t...

Model KCLONE-4NVME Interface M.2 M-keyed M.2 B+M-keyed Drive Support PCIe based NVMe SSD SATA based M.2 SSD Display Full-color 4...

The duplicator will not boot or freezes curing boot. The device has media (drives) connected to it while powering on. Power the device off and disconnec...

Statement of Volatility for the 4-Target and 11-Target NVMe Duplicators SoV NVMe Duplicator.pdf